Finally an affordable, modular pickup system in an easy to install package. There is no Blend mode in this configuration. GRAPH TECH GHOST & THE BASS GUITAR. Note that you actually get more control over your sound with separate pots because it allows you to control how hard each pickup drives effects down the line. Wiring - Ghost, 3 way switch, 2 vol, 2 tones, one ghost vol... Billy Hell. The added passive components are used to ensure that the power switching of the Acousti-Phonic still works normally (even when the switch is in the bypassed position), *Passive components available from Graph Tech upon special request, Seymour Duncan Plays Private Show for Guitar Electronics, GuitarElectronics.com Cadillac CTS-V Wins 2017 SCT Championship, Guitar Electronics Starts Custom Wirirng Diagram Service. There is no blended (mono) mode available in this configuration. Dual Jack Mag Bypass Mags go straight out to one 1/4" jack (true bypass) and acoustic goes to another 1/4" jack, the Stereo Switched Jack that comes with the Acousti-Phonic. Dual Jack Blend Dual jacks with blended signals available when a mono plug is inserted in the Stereo Switched Jack only. Standard Machine Heads Installation Guide. Account & Lists Account Sign in Account & Lists Returns & Orders. This can be used in the case that the battery dies and you still want to be able to play your magnetic pickups. The added passive components are used to ensure that the power switching of the Acousti-Phonic still works normally (even when the switch is in the bypassed position) *Passive components available from Graph Tech upon special request. Try Prime Cart. Musical Instruments. Ratio Machine Heads 5. Acousti-Phonic with Quickswitch Standard Acousti-Phonic wiring with optional Quick Switch for magnetic/both/acoustic switching.. Acousti-Phonic Kit Standard Acousti-Phonic wiring with the acoustic volume pot and Mid/Dark push/pull switch plus a Quick Switch. The Acousti-Phonic is held in mono mode by grounding the ring contact permanently, but the signal going into it is acoustic, so that's all that appears on the Tip. Note the Switchjack is designed for acoustic guitars and comes with a strap-nut, but this can be removed and replace with a regular but for use with electric guitars. To get acoustic-only on the 13-pin connector, leave the magnetic pickups disconnected. If you want to know more or withdraw your consent to all or some of the cookies, please refer to the, Modular pickup systems hexpander midi interface | acousti-phonic pre-amp. The Switchcraft Switchjack has four lugs like the Stereo Switched Jack that comes with the Acousti-Phonic, but the switch works in the opposite way, so it can't be wired the same. Pin 7 Harness For use when the Hexpander is used without an Acoisti-Phonic. Get studio quality acoustic tone or MIDI compatible output at the flick of a switch. Push Pull as a QuickSwitch Use the switch in push/pull pot as the QuickSwitch but the push/pull has only 2 positions so you get mag/acoustic instead of mag/both/acoustic. Skip to main content Hello, Sign in. See all 6 articles. Note that players sometimes add this thinking they will need it, and never use it because they love the Acousti-phonic sound the way it is. Hexpander First Row These connections are on the Hexpander's pass-through connector to the Acousti-phonic when they're piggybacked together, so they're the same as the standard installations for the Acousti-Phonic. Account & Lists Account Sign in Account & Lists Returns & Orders. Amazon.com: Graphtech Ghost Interface Wiring Harness PD-0512-00: Musical Instruments. Les Paul Toggle Switch This diagram shows how to wire a Les Paul style 3-way toggle switch in place of the QuickSwitch. Page 51 Hexpander-only and Dual Board Connector “Piggyback” installations 13-pin Hexaphonic Output Jack ghost Hexpander MIDI interface board (fits hole: 1” x 1-1/4” x 1-1/4” deep) (dimensions: 1-1/8” x 1-5/8” x 1/2”) HEADER PINS Interface Wiring Harness SIGNAL ROW (all colored wires) Graph Tech Ghost Volume Potentiometer Wiring Harness Graph Tech Guitar Labs. *Please note that there will be an audible “thump” sound when the Acousti-Phonic is turned on, This bypass switch can be installed if you would like connect your magnetic pickups directly to the output (bypassing the Acousti-Phonic) but will keep the battery connected when in the bypass mode. There is no stereo mode available in this configuration. Acousti-Phonic with Tone Control Add a tone pot to the ghost acoustic volume. Hexpander Second Row The standard connections for the Hexpander pickups, optional switches, and volume pot. I mean, to me, out-of-phase wiring always sounds like a mistake was made somewhere, and I'd never have it on my guitar, but some of you guys make a point to add out-of-phase options to your super custom gear. In the booklet that shows wiring to the the board ther diagram should be color and not black and white. Skip to main content Hello, Sign in. That way, you don't need a 1/4" cable plugged into the guitar. The Quick Switch plugged into the Hexpander will control these signals on the 13-pin, but not on the 1/4" jack. *Please note that there will be an audible “thump” sound when the Acousti-Phonic is turned on, Mag Bypass Push/Pull - Scheme 2 This bypass switch can be installed if you would like connect your magnetic pickups directly to the output (bypassing the Acousti-Phonic) but will keep the battery connected when in the bypass mode. Current Stock: Quantity: Decrease Quantity: Increase Quantity: Add to Wish List. Discussions Graphtech Forums Tips and Tricks. Page 18: Ground Loops fi rst. *, Manual will be automatically added to "My Manuals", Page 6: Convert Mag Tone Pot To Acoustic Volume, Page 14: Acoustic Volume And Magnetic Input. This wiring delivers both Mono and Stereo modes. Amazon.com: Graphtech Ghost Interface Wiring Harness PD-0512-00: Musical Instruments. Graph Tech Ghost Pin 7 Output Harness If you are installing the Hexpander without the Acousti-phonic, you may want to add this optional pin-7 wiring harness so that your guitar's mag and/or piezo signal goes down the 13-pin MIDI cable and out the back of the converter. The Acousti-Phonic is help in mono mode by grounding the ring contact permanently, but the only signal going into it is acoustic, so that's all that appears on the Tip. Im installing my first ghost system at the mo (with the pre amp), and Ive hit a bit of a snag... My question regards the jack socket wiring, as I plan to use a barrel style stereo jack (with 3 connectors) rather than the supplied unit with 4. Stereo switched Jack (no routing required), Acoustic volume with Mid/Dark switch *opt. Wiring - Ghost, 3 way switch, 2 vol, 2 tones, one ghost vol... Billy Hell. Try Prime Cart. The standard connections for the Hexpander pickups, optional switches, and volume pot. Note this requires the addition of an acoustic volume pot, or you can omit the pot and get acoustic out at full volume all the time by connecting the yellow and orange wires together. Connect the green wire to the magnetic pickup system at the 1/4" jack. When a mono 1/4" plug is inserted the second jack (also a Stereo Switched Jack), mag is on the first. Try the Acousti-phonic first without a tone pot, and add it only if they feel its necessary. Standard Graphtech Ghost Acousti-Phonic & Hexpander Installations. This may be a useful option for guitars that can't use the Stereo Switched Jack, such a those with a deep barrel jack. To get magnetic pickups only on the 13-pin connector, omit the yellow and orange wires. This will more applicable for live performance.
2020 graphtech ghost wiring